1) Design on Drop Weight Tear Test Damper for HICOM Petropipes Sdn. Bhd. Sg. Petani, Kedah (1996) 

Amount : RM 10,000.00

Project Output : A damper system made of natural rubber sourced locally by Rubber Technic Kuala Kangsar to replace a complicated German design of hydraulic system

2) Fatigue Testing of Steel Reinforcement Barof Various Diameters (8mm to 32 mm) for Malayawata Steel Sdn. Bhd. Prai, Penang (1996 – 1998)

Amount : RM 32,000.00

3) Tensile Testing of Piano (Steel) Wire for a Company in Ipoh (1998)

Amount : RM 800.00

4) Manufacture of Spacecraft Fit Check Model for Astronautic Technology Sdn. Bhd. (1998)

Amount  :  RM 8,720.00

Project Output : An project involving construction (machining of Tiungsat satellite model for various fitting)

5) Stability Study for Pole Planting Machine for Tenaga Nasional Nibong Tebal (2000)

Amount : RM 250.00

Project Output : A stability report on a device used to erect the pole in electrical transmission 

6) Leadframe Plating Head Reengineering for Dynacraft Industries (M) Sdn Bhd (2000)

Amount :   RM 84,000.00

Project output :  A new design for the elatomeric seal used in the plating head

7) Design and Development of Liquid fertilisers and Pesticide Spray Mechanism for Large Scale Rice Plantation Federal Land Rehabilitation and Consolidation Authority FELCRA Wilayah Perak (2002)

Amount:  RM 230,000.00

Project output: A mechanism with the capacity of spraying 50 litres per minute of liquid fertilisers and pesticides capable of covering about 0.5 hectare per minute

8) Small DC Motor Noise and Vibration Improvement for Matsushita Electric Motor Sdn. Bhd. (2002 - 2003)

Amount: RM 33,326.00

9) Calculation of Maximum Deflection and Maximum Stress for Escalator for MS Elevators Malaysia Sdn. Bhd. (2003)

Amount: RM 800.00

10) Failure Analysis of One Hydraulic Press Component (Shaft) and Delivery of Report for UNIPAC Engineering (Pg) Sdn. Bhd. (2004)

Amount: RM 1,985.00   

11) Vibration Test for OSRAM Organic Light Emitting Diodes (OLED) Display, OSRAM Penang. (2005)

Amount: RM 1,500.00

12) Modal Analysis of the UAV at CTRM Sdn. Bhd. Melaka. (2009)

Amount: RM - Picture

13) Vibration and Noise Measurement of Rail Coaches for SCOMI Monorail, Selangor. (2011)

Amount: RM 1,800.00 Picture

14) Strain Calculation for Capacitor on PCB for Benchmark Electronics (M) Sdn. Bhd. (2012)

Amount: RM 2,000.00

15) Damping and Resonance Measurement of Rubber Mount for Kozomi Rubber (2012)

Amount :RM 2,400.00  

16) Modal Analysis of the Proton Waja Exhaust for MFI-UniKL, Selangor. (2013)

Amount: RM - Picture

17) Modal Analysis of the Various Beam Materials for UTM, Johor. (2014)

Amount: RM -

18) Absorbtion Coefficient Measurement of the Concrete Materials for Politeknik Kulim, Kedah. (2015)

Amount: RM 2,500.00

19) Car Floor Board Vibration Testing for Lexus NX 200t, Penang. (2016)

Amount: RM 1,855.00

20) Ground Vibration Measurement of the UWC Plant, Penang(2017)

Amount: RM 5,035.00

21) Vibration Analysis of the TNB Chenderoh Hydropower Station, Perak(2017 - 2018)

Amount: RM 108,200.00